RoomMatch® RM9020 array module delivers superb audio quality for fixed-installations in almost any room size, shape, acoustic requirement or budget. Overcoming the acoustic limitations of both line array and point-source conventional designs, RoomMatch® modules form a new class of curvilinear array that allows seamless audio quality, with consistent front-to-back and side-to-side tonal balance.
An accessory installation bracket that allows a single RoomMatch full-range array module loudspeaker to be mounted on flat surfaces, such as building walls or ceilings. The brackets allow pitch angle adjustment from 0° up to -90°, depending on which RoomMatch module is used. The bracket attaches to the side-plate rigging hardware of each RoomMatch full-range module. Kit of left and right pair with fasteners. Net weight: 15 lb (6.8 kg) per Left/Right kit. (The RMBRKT bracket is NOT intended for use with RoomMatch subwoofer modules.)
Use with bottom-most array module to provide third-point suspension to building structure to allow more extreme downward angle of arrays than possible from 2-point, gravity-hang suspension. The RMPULL can also be used as a “mini frame” for suspending 1 or 2 modules. Single bracket with fasteners. Net weight: 26 lb (11.8 kg).
Use with large-array frame to accommodate subwoofer module mounting behind primary array. Also provides additional shackle mounting pickup points to allow more extreme angles for 2-point mounting. Kit of left and right pair with fasteners. Net weight: 88 lb (40.0 kg) per Left/Right kit.
Use with large-array frame to accommodate subwoofer module mounting behind primary array. Also provides additional shackle mounting pickup points to allow more extreme angles for 2-point mounting. Kit of left and right pair with fasteners. Net weight: 70 lb (31.8 kg) per Left/Right kit.
Set of 4 quick-release pins designed to replace the graded M10 fasteners for module-to-module connections. May be used with RoomMatch® full-range or subwoofer modules. Net weight: 1 lb (0.5 kg) per set.
Optional accessory that installs in the input panel of RoomMatch full-range modules to allow attenuation of the bottom-3 compression drivers as compared to the top 3 drivers. This allows for more uniform sound pressure levels for specific module configurations and coverage areas. Net weight: 2 lb (0.9 kg).
RoomMatch Ground stack Kit accessories are designed to accommodate ground stack arrays of up to three (3) RoomMatch modules for occasional movement to different locations, such as temporary side-stage fills for performing arts centers that require differing seating configurations. RoomMatch modules and ground stack accessories are not recommended for tour sound applications that require daily setup and transportation.
Use with up to three (3) RoomMatch modules for ground stack arrays. Requires subwoofer module in bottom position. Kit includes two (2) frame rails, four (4) M10 x 40mm fasteners, and four (4) leveling feet. Caster kit is available separately. All ground stack array configurations must use the base kit. Overall rail dimensions: 3.0" H x 4.9" W x 54.4" D (75 x 125 x 1382 mm). Net weight: 54 lbs (24.5 kg).
Use with RMGSBK ground stack base kit. Replaces leveling feet included in base kit. Set of four (4) casters with sixteen (16) M8 x 25 mm fasteners. Overall caster dimensions: 5.0” diameter and 1.25” width (127 mm x 32 mm). Net weight: 10 lbs (4.5 kg).
Attaches to subwoofer module and mounts one or two RoomMatch full-range modules, allowing pitch angle adjustment from 0 to 30 degrees down pitch (differs by module vertical coverage pattern). Complete pitch bracket is formed by assembly of pitch plate that attaches to subwoofer module and mounting bar that attaches to RoomMatch full-range modules. Kit contains two (2) pitch plates, two (2) RoomMatch full-range module mounting bars, four (4) M10 x 40 mm fasteners, and four (4) M10 x 30 mm fasteners. Pitch brackets also require use of four (4) M10 x 30 mm fasteners (15 mm socket size) supplied with RoomMatch full-range modules. Net weight: 19 lbs (8.6 kg).
Provides subwoofer-to-subwoofer module connection for ground stack arrays. Includes pair of subwoofer connection plates and eight (8) M10 x 40 mm fasteners. Note: RMGSSB bracket is NOT required for the bottom subwoofer connection to the base kit; subwoofer modules bolt directly to the base frame rails. Net weight: 7 lbs (3.2 kg).